Thursday 18 October 2012

Light Boxes


Description and Use
Light boxes are in many ways development from the glass easel. The glass easel was used in studios to wax up the painted glass and display it as it would be seen in a window. Sometimes the glass painters painted across all the glass at once, so this method enabled them to see the results immediately.
Nowadays people tend to use back lighting for these and other purposes, so the light box has become more popular. Some of the uses are outlined here:

The light box is very useful when tracing or altering designs. The back lighting enables you to use other paper than tracing papers to transfer the design elements. You can fold the paper along the lines of symmetry to check on how the lines match, or to copy the lines from one side onto the other side at the designing and cartoon stages.

The light box can help select glass colours either initially or when the main pieces have already been established. The combination of the glass over light shows how they interact with each other. At later stages when the main glass is cut, it can help avoid unwanted bright or dull areas.

Possibly the most common use is in cutting dark or opalescent glass. The additional light allows you to see the cartoon through the glass and so cut directly from the cartoon. This can be enhanced by blanking out the excess light from around the glass or cartoon.

The light box enables the arrangement of the cut glass pieces to be assembled to view the colour balance and have a virtual view of how the panel or window will look as a finished piece. An additional step toward the result is gained if each piece is outlined in white-board markers – use black pens - to represent the lead or copper foil and their widths. This stops the light between the pieces from causing you pupils to contract, and gives a more accurate representation of the appearance of the final pane.  White-board markers can just be wiped off the glass without using spirits.

The light box is important in painting. The back lighting shows the effect of the painted line or level of shading immediately. This allows adjustments to be made quickly and accurately before firing,

Depending on how the light box is built, it also can be used as display lighting. This can be as up-lighting or backlighting.

Requirements

The top surface needs to be firm and scratch resistant. Toughened or laminated glass is good for this. The larger area covered, the thicker the glass needs to be, or there needs to be support under the glass to avoid breakage from pressure. The toughened or laminated glass resists breaking from dropping material onto the light box.

You need to have daylight corrected light sources for you light box, especially if you are doing any glass selection on it. Fluorescent tubes are easily available, but other light sources can be used. You need to have ventilation to allow the heat generated by the lights to disperse. Fluorescent tubes do not generate much heat and so are the common choice for lighting.

You need diffused, even light across the whole surface. This requires a diffuser and there are a number of solutions. You can sandblast the back of the top sheet, but I find this does not provide enough dispersion. You can sandblast both sides, which gives better dispersion of the light, but is difficult to clean and so needs another sheet on top. The best dispersion of light comes from using a sheet of opaque acrylic with about 80% light reduction. The difficulty with this is that it is flexible and needs support if any glass cutting is going to be done on the surface. I place the acrylic sheet underneath a sheet of 6.4mm laminated glass. This gives both solidity and dispersion.

Light is a central consideration in building the light box. The intensity is controlled by two things mainly – The number of lumens and the intervals of the light sources. The best way toward even light distribution even with good dispersion sheets, is to have multiple light sources. It would be possible to pack the box with light fixtures, but this is expensive and generates a lot of heat. It also may make the light too intense to be comfortable to work with. In general, fluorescent tubes placed at about 150mm centers apart will provide all the light you will need.

To make sure you get all the benefit of the light you need to build an enclosed box with ventilation holes or slots that is painted matt white on the inside. This allows the light to be reflected upwards through the surface without bright spots that can be caused with gloss paint.

You need to consider the size of the box in terms of surface area. This will relate to the space you have available and the scale that you work at. In addition to a separate surface the box can be an area of the work bench, or covered by a separate work board – whether permanent or temporary.

The height of the box will need to be considered. Will you be sitting or standing while working at the light box? It needs to be high enough in either case for you to maintain a straight back.

You need to consider the ability to screen parts of the light so the light is directed only at the work area. Large areas of light will overwhelm the glass, making it appear darker than the finished piece will actually be.

You need to think about the amount of flexibility your box requires. If you want to use it as part of your display equipment, it needs to be mobile and relatively light. This will interact with the materials to be used in construction.


Construction

Light boxes can be constructed in a variety of ways. The simplest to construct is the free standing, horizontal, single purpose light box.

You need to consider the size of the box in terms of surface area. This will relate to the space you have available and the scale that you work at. Having determined the surface area required or possible, you need to think about the height. The top should be of a height so you can stand or sit with a straight back while drawing, cutting or painting. This will vary according to your height and whether you will be standing or sitting. Typically these heights will be the heights of the benches and desks you already use, but you need to check again that you are actually working with a straight back, as this will reduce the fatigue you might otherwise experience.

Note that if the box is going to be sat at, it will need to be narrower to be able to reach to the opposite side. If you will be standing at the box, it can be at least half again as wide as the sitting version. A sitting version will also affect the depth of the box containing the lights. It may not be possible to have anything deeper than 100mm. This will produce some problems with the evenness of the light, but nothing that will make it unusable.

Then you need to consider the depth of the box. In principle, the deeper the box the better diffusion of the light. But there are limits. If the box is really deep, more lights will be required, and potential storage space is lost. I recommend about 150mm for the depth of the box. I then place the fluorescent tubes at 150mm centres across the box. It does not matter which direction they are oriented. That will be more determined by the available fittings and the dimensions chosen.

The flexibility you have in building your own box includes a number of things which could be constructed separately or in combination.

You can cover the light box with a sturdy work board to do all kinds of work on top. So this makes a combination light box and work bench. This top can be hinged so you don't have to lift it off each time you want to use the bench. It should have some support mechanism so it does not fall on your or your work. I have used a chain that allows the board to go back just beyond the vertical. These chains can sometimes get in the way of your work.

In addition to a separate surface the box can be an area of the work bench. The important element is that the rest of the surface of the bench should be at the same level as the light box top. Any variation runs the risk of breaking the glass you may be working on. The cover for this can be hinged to protect the surface when the light is not needed.


Often you will be working on pieces smaller than the illuminated area. It is possible to arrange things so that each light fitting can be turned on and off independently to allow light reduction or intensification as you need. It is simpler to have sheets of opaque card to place around your work area to reduce the extraneous light that will overwhelm the glass that you are selecting or painting, for example. In the case of too much light the glass or the painted lines and shading look darker than they really are as a result of your pupils contracting against the light.

You could add a variation to allow the light box to be used as a near vertical illuminated glass easel. This requires a set of hinges, a ledge on the hinged side and a support of some kind at the back, similar to a piano lid support. This is most useful in painting and in waxing up the pieces to view the whole panel before leading or foiling.

You need to think about the amount of flexibility you require the box to have when considering the materials to be used. If you want to use it as part of your display equipment, it needs to be mobile and so relatively light. This will interact with the materials to be used in construction. In this case you may want to make greater use of metals for their strength in relation to weight. 

 You probably will use opaque acrylic sheet as the surface. If you do, you will need to give it internal support to keep it from bowing. The best for this is another piece of acrylic – clear this time – glued to the top sheet and to the bottom of the box between the light fittings.


Working surface

I recommend your top should be 6.4 laminated or 4mm toughened glass for anything up to 610 by 1000mm. If it is larger, you should go to 6mm toughened, as 8.6mm laminated glass is pretty expensive. I suggest glass because it is strong, rigid, scratch resistant and easy to clean.

You can use a router to form a ledge for the glass to sit on. You can use a less machine intensive method, by nailing thin battens or quarter rounds around the glass. But the structure which confines the glass should be no higher than the glass surface. If it is higher than the glass, you can simply plane or sand it down. Insure there is no part of the fixings of the glass higher than the glass surface. This is especially important when cutting glass on the light box. If the surround is higher, you run the risk of breaking glass that is for one reason or another overhanging the edge. It also makes it easier to get the glass on and off the light box.

To get the appropriate diffusion you need to do more than sandblast the underside of the glass. While this will provide some diffusion, it is not enough. You can put another sheet of glass, sandblasted on both sides, underneath the top sandblasted sheet to provide good dispersion of the light. However, I have found a 3 or 4 mm sheet of white acrylic that is 70% -80% opaque provides the best diffusion of the light elements, even though it is more expensive than glass.

You also need to have a method to be able to get at the lights. This can be by having a removable section of the boundary. You can also make use of the ventilation holes, if appropriately placed, to lift the glass. A portion of the box sides can hinge to allow access to the lights through the side, although this is more awkward than fitting from above.


Lighting

Light is a central consideration in building the light box. 

The best way toward even light distribution even with good diffusion sheets, is to have multiple light sources. I recommend placing them at the same distance apart as the depth of the box. It would be possible to pack the box with light fixtures, but this is expensive and generates a lot of heat. It also may make the light too intense to be comfortable to work with. If you can control the general lighting of your studio and you can turn it off or down, you will not need such intense lighting in your box.

An alternative, but more complicated method is to build the light box with baffles so the light is never directly under your work. Commonly, this would require the box to be built wider than the glass upon which you will be working. The light reflects from the sides and bottom of the box to give an even light. In this case, the single sandblasted surface would be sufficient to disperse the light and keep your eye focused near the surface of the glass or cartoon on which you are working.

You need to have daylight corrected light sources for you light box, especially if you are doing any glass selection on it. Fluorescent tubes are easily available, but other light sources can be used if they can be found in daylight colours. Fluorescent tubes do not generate much heat and are available in daylight corrected colours. So these are the common choice.

You still need to have ventilation to allow the heat to disperse, though. Ventilation can be provided in a number of ways ranging from drilling holes in the sides, to providing a slot in the side or bottom.

You need to have access to the light fittings to replace bulbs. It is easiest if this is by removing the glass top. You can provide tabs on or under the glass to lift it with, but these often interfere with other uses. You can use the ventilation holes if they are high on the box to stick a lifter under the glass to be able to grasp the edge. You can have a removable section to the beading that holds the glass top in place. You can provide a couple of finger holes at the top edge of the box to enable more direct lifting of the glass without disturbing any of the box fittings.

Another important element in getting the maximum amount of light out of your box is to paint the inside white. This should be a matte or at most silk finish. Any glossier finish will produce bright reflective areas. Shiny surfaces such as aluminium foil also produce these unwanted bright areas. In fact, a matte white surface gives more apparent light than aluminium foil in the light box.

The lights should be wired in series so they all come on at the same time. It is of course possible to have a switch for each fitting, to vary the intensity of the light for the work you are doing. This does add a bit to the expense, but may be valuable for your way of working.